S.ttl. Press "Open". Place the test CD disc PATD-012 on the Deck A. Place the recording CD-RW disc (see Note: 4-5-1) on the tray (Deck B) as prompted by the show and push "OK". Page 44 RCD-W500C 4-3. CD-RW Playback Adjustment 1) Select the menu as follows. Page 47 RCD-W500C 4-5. CD-RW Recording Adjustment and Self Record/Playback Check Select the menu as follows. Erase it in the adhering to course of action, to reuse the CD-RW disc to electrical adjustment, or to use a disc other than blank. Be positive to erase it in the following process, to use the disc utilized for electrical adjustment for other uses. Page 39 RCD-W500C CDM65-RBD2 Electrical Adjustment 4-1. Laser Power Adjustment Start up the TeraTermPro and established the swap S510 on the jig to "CONTROL". Page 40 RCD-W500C 6) When the display screen as revealed in Fig. 4-6 appears, position the probe of the laser electrical power meter on prime of the optical laser unit, and press "OK". " seems. (Fig. 4-34)(The tray opens.) 4 Fig. 4-34 NG Judgment Result Indication 4-3-1. Playback Measurement NG! Contents: This message appears when the BLER (Block Error Rate) in the course of playback is outside the house the specification.



Tray Close NG! The tray has not shut within just the specified time. Page 50 RCD-W500C 4-7. NG Message List Message Cause Tray Open NG! four Fig. 4-18 13) Check that the information "Laser Power CAL completed! 3) When there is no error, the exhibit as revealed in Fig. 3-26 appears. There are two main pathways in which sodomy rules have been decriminalized: judicial invalidation and repeal of the legislation by vote of laws. For schematic diagrams. Note: • All capacitors are in µF unless of course otherwise noted. F. fifty WV or less are not indicated besides for electrolytics and Top Porn Lists tantalums. S.ttl. Press "Open". As prompted by the concept demonstrated in Fig. 4-51, clear away the disc from the tray and press "OK". Page forty two RCD-W500C 12) When the screen revealed in Fig. 4-18 seems, clear away probe of the laser energy meter and press Ok. Page forty one RCD-W500C 10) Adjust the laser output energy as follows. RCD-W500C 6-7. Printed Wiring Boards - CD-R Section (Side B) - • See page 55 for Circuit Boards Location.



RCD-W500C 6-4. Printed Wiring Boards - SENSER/MOTOR/SW Section - • See site fifty five for Circuit Boards Location. RCD-W500C 6-5. Schematic Diagrams - SENSER/MOTOR/SW Section - • See webpage eighty three for IC Block Diagrams. RCD-W500C 6-8. Schematic Diagrams - CD-R Section (1/4) - • See web site fifty five for Waveform. RCD-W500C 6-3. Schematic Diagrams - BD Section - • See web page fifty five for Waveform. • Semiconductor Location Ref. NOT Used (LASER Power METER) (TO JIG) • Semiconductor Location Ref. MOTOR • Semiconductor IC104 Location Ref. RCD-W500C 6-2. Printed Wiring Boards - BD Section - • See site fifty five for top Porn lists Circuit Boards Location. RCD-W500C 6-6. Printed Wiring Boards - CD-R Section (Side A) - • : Uses unleaded solder. • See web page seventy seven to 79 for IC Block Diagrams. Page fifty four RCD-W500C 3) Check that the time screen as demonstrated by the arrow mark in Fig. A-4 is up to date following a even though. Page forty eight RCD-W500C 6) As prompted by the concept shown in Fig. 4-48, test that the waveform as shown in Fig. 4-47 appears on an oscilloscope.



Page 45 RCD-W500C Check that the information "CDRW PB-CAL finished! Fig. 4-37) four Fig. 4-37 5) When the information as revealed in Fig. 4-38 appears some seconds afterwards, stop playback (1X) and find 4x of the test manner (refer to web site 21, Play Speed Selection Mode (Deck A)) Playback Speed. 4 Fig. 3-26 4) When error has transpired, the exhibit as revealed in Fig. 3-27 appears exhibiting error background. Press "Open". (Fig. 5-1, 5-2) four Fig. 5-1 four Fig. 5-2 Press the "RESET" button (SW101) of the jig as prompted by the show. Page 38 RCD-W500C 2) Press the "RESET" button (SW101) of the jig as prompted by the display screen. S.ttl. Press "Open". 2) Place the test CD TCD-W091W on the tray as prompted by the screen and push "OK". Instead, Lucy was "obtaining a infant," "expectant" or "with kid." During the nineteen sixties, actresses couldn't show their navels on exhibits these as "I Dream of Jeannie," "Gilligan's Island" and "Gidget" - must've been the connection in between stomach buttons and pregnancy that censors feared. RCD-W500C - CD Section - IC101 Digital SERVO Digital Signal PROC. Page 43 RCD-W500C Note :The crystal clear RF sign waveform indicates that the shape " " can be evidently distinguished at the middle of the waveform.